Midco Unipower A-Series Instrukcja Użytkownika Pobierz pdf

Installation and Service Instructions

Midco International Inc.

4140 West Victoria Street Chicago, Illinois 60646

tel 773.604.8700 fax 773.604.4070 web www.midco-intl.com

199

8449-11

Printed in U.S.A.

In the United States, installation must conform with local codes or

in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1-latest edition available from American

National Standard Institute. Further reference should be made to

the recommendation of your fuel supplier.

In Canada, installation must conform with local codes or in the

absence of local codes, with Installation Codes for Gas

Burning Appliances and Equipment, CGA Standard

CAN/CGA 1-B-149.1 or 2. When the conversion burner is used

on a Forced Air Central Furnace, the two yellow and black

warning labels in the literature envelope shall be attached in

accordance with Installation Code, CGA Standard CAN/CGA

1-B149, Clause 5.4.4.4. Further reference should be made to

the recommendation of your fuel supplier.

WARNING: Additions, changes, conversions and service

must be performed by an authorized Midco

representative, service agency or the fuel supplier. Use

only MIDCO specified and approved parts.

INSTALLER:

Inform and demonstrate to the user the

correct operation and maintenance of the gas

utilization equipment. Inform the user of the hazards

of storing flammable liquids and vapors in the

vicinity of this gas utilization equipment and remove

such hazards. Affix this manual and associated

literature to the conversion burner.

CODE COMPLIANCE IS THE SOLE RESPONSIBILITY OF THE

INSTALLER.

USER:

Retain this manual for future reference. If other

than routine service or maintenance as described in this

manual and associated literature is required, contact a

qualified service agency. DO NOT ATTEMPT REPAIRS.

An inadvertent service error could result in a

dangerous condition.

Unipower A-Series

Gas Burners

BURNER

MODEL

BILL OF MAT'L

NUMBER

DATE CODE

WIRING DIAGRAM

PIPING DIAGRAM

START-UP INSTRUCTIONS

FOR SERVICE CONTACT:

name

address

phone

SSAAFFEETTYY IINNFFOORRMMAATTIIOONN TTEERRMMSS:: The following terms are used to identify hazards, safety precautions or special notations

and have standard meanings throughout this manual. When you see the safety alert symbol and one of the safety

information terms as shown below, be aware of the hazard potential.

WARNING: Signifies a hazard that could result in personal injury or death.

CAUTION: Identifies unsafe practices which would result in minor personal injury or product and property damage.

Warning: If the information in these instructions

is not followed exactly, a fire or explosion may result,

causing property damage, personal injury or death.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in the building.

• Immediately call your gas supplier from

another building's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

1 2 3 4 5 6 ... 11 12

Podsumowanie treści

Strona 1 - Unipower A-Series

Installation and Service Instructions Midco International Inc.4140 West Victoria Street Chicago, Illinois 60646tel 773.604.8700 fax 773.604.4070

Strona 2 - Part 1 Installation

Part 2 ServiceCAUTION: Do not tamper with the unit or controls. If trouble occurs contact yourserviceman.CAUTION: Be sure that the main and pilot manu

Strona 3 - Heating Appliance

XI Blower and MotorXII Gas Pressure RegulatorXIII Main Automatic SafetyShut-Off ValveV48 Diaphragm Gas Valve (Not for use in Canada)V5055 Valve Body w

Strona 4

V5055 Valve Body with Motorized Actuator Cont.XIV Automatic Gas Valve Leak TestXV Flame SafeguardXVI Special Equipment Do not disassemble the valv

Strona 5

Part 1 InstallationI SpecificationsBurner Style Power TypeFlame Safeguard Instantaneous electronic typewith flamerod detection (flame rectification).•

Strona 6

III Preparation of theHeating ApplianceContinuedIV Combustion Chamber Make sure that the boiler gauge glass is clean so that water level can be ea

Strona 7 - V Chimney and Flue Pipe

For warm-air furnaces or Scotch Marine boilers with tubular combustion chambers, thecombustion chamber length must be great enough to exceed the

Strona 8 - VII Gas Piping

IV Combustion ChamberContinuedDetailed information is available on request. Since firing door installations will generally leave no openings for f

Strona 9 - VIII Burner Start-Up

Figure 7: Conventional Boiler—Small FireboxFigure 8: Tubular Combustion ChambersFigure 9: Firing Door Installation in Three Pass BoilerIV Combustion C

Strona 10 - Part 2 Service

V Chimney and Flue PipeThe chimney should be inspected for unsafe conditions such as deteriorated masonryand excessive soot or other blockage or poten

Strona 11 - Shut-Off Valve

VI ElectricalVII Gas Piping The burner when installed, must be wired and grounded in accordance with local codes or inthe absence of local codes,

Strona 12

VII Gas Piping Cont.VIII Burner Start-Up In higher gas pressure systems (over 14" W.C.) it is very important to install the properpressure re

Komentarze do niniejszej Instrukcji

Brak uwag

Midco Unipower A-Series Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Ekwipunek Midco Unipower A-Series. Midco Unipower A-Series User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Midco Unipower A-Series